UG-500 Standard Pneumatic Grinding Machine
| Inlet Pressure | weight | sizes |
|---|---|---|
| 90psi ( 6.2kg / cm2 ) | 110g | Ø20 x 160L ( mm ) |
General Assembly
In order to make the pneumatic tool to achieve the best condition and extend its life, need to connect the three points of the combination of use, in order to achieve the purpose of filtering water, control the air pressure and lubrication.
Requirements for improved performance and service life.
In order to make the pneumatic tool to achieve the best condition and extend its life, need to connect the three points of the combination of use, in order to achieve the purpose of filtering water, control the air pressure and lubrication.
- Be sure to check that there is enough lubricant in the oil reservoir of the three-point combination before using the pneumatic tool.
- Setting the inlet pressure of the three-point combination at 90psi (6.2kg/cm2) is optimal for use.
- Check to see if the 3-point water filter is full before use, and drain it if it is.
- Adjust the oil intake of the 3-point combination, recommend about 2CC per minute (under frequent use).
- If you are on holiday or haven’t used the air tool for a long time, please increase the lubrication volume of the 3-point combination to 4cc per minute when you turn on the air tool for the first time, and let the air tool idle at a low speed for 20-30 seconds, so as to let the lubrication oil lubricate each part, and then adjust it to the normal speed to use the air tool.
- Choice of lubricant: Do not use a lubricant that is too viscous. We recommend the use of recycled oil R32.
Operating conditions, start/stop settings:
- The ON / OFF switch is operated by rotating the valve body toward the user, counterclockwise to ON (open) and clockwise to OFF (closed).
※ Make sure the switch is in the “OFF” position before using the pneumatic tool. - When turning on the switch of pneumatic tool, please rotate it 90°, so that the maximum operating speed can be reached. If the angle of rotation is too large, it will not only have no effect but also cause the switch valve to fall off and be damaged.
protective device
Please wear any necessary protective equipment such as ear defenders, goggles, safety apron, helmet, gloves, etc. when using.
Storage of pneumatic tools after use
The tool must be kept in a clean and dry place, and it is recommended to store it in a constant temperature place to avoid sudden temperature changes. Do not put down the pneumatic tool until it has come to a complete stop during operation.
Detailed safety rules and reminders
Safety is a major consideration when using pneumatic tools. Pneumatic tools must be operated under safe conditions, please read the following clauses before use and use pneumatic tools safely.
- This pneumatic tool is designed for industrial use such as grinding or engraving and fine polishing, and should not be used on humans!
- Check the air pressure before operation. Air pressure below 90psi (6.2kg/cm2) will reduce speed and force, but above 90psi will result in overspeed operation, which is very dangerous and will shorten the life of the tool!
- Please use good quality abrasive consumables, do not use damaged or poor quality consumables.
- If the noise level exceeds 85dB(A), the operator must wear earplugs or ear protectors.
- Prolonged use by the operator may result in work-related injuries due to vibration, especially to the palms and arms. Work-related injuries caused by vibration depend on many factors, such as the type of consumables used, the manufacturing process, the user’s physical condition, the working environment, the working hours, the temperature, and so on. Therefore, operators using pneumatic tools must work in accordance with the provisions of ISO 5349.
- When using, pay attention to hair, loose clothes or ties, etc. so as not to be caught by pneumatic tools.
- The working area should be well ventilated, preferably with a dust collector to avoid inhalation of dust or gas discharged from the air compressor.
- If any lubricant gets in your eyes or is accidentally ingested, seek medical attention immediately.
- Do not modify or disassemble air tools without the manufacturer’s permission or consent.
- It is important not to touch the spinning consumables while the pneumatic tool is in operation.
- Make sure that the generated sparks will not hurt people around you or splash flammable substances, etc.
- Make sure that the workpiece being processed has been properly supported or fixed to prevent the workpiece from flying out.
- Do not use air hose other than the standard equipment, and do not pull the air hose violently when using them.
Safety recommendations for recommended clamping length, number of revolutions, extension length
Note: The clamping length L should not be less than 10mm.
| ØD ( mm ) | T ( mm ) | Recommended Consumable Extension H (mm) | ||
|---|---|---|---|---|
| 13mm | 25mm | 38mm | ||
| 3.0 | 13 | 105,000rpm | 64,000rpm | 46,650rpm |
| 6.0 | 13 | 60,000rpm | 38,000rpm | 26,250rpm |
| 9.5 | 13 | 45,370rpm | 28,500rpm | 21,000rpm |
| 9.5 | 25 | 26,250rpm | 18,750rpm | 14,250rpm |
| 13 | 13 | 34,500rpm | 22,500rpm | 16,870rpm |
| 13 | 25 | 20,620rpm | 13,870rpm | 10,120rpm |
- L = Clamping length
- H = Consumables protruding length
- T = Abrasive length
- ØD = Grinding Rod Diameter
Any questions? Contact HonWay
